Just wondering how many Four Winns Liberator owners are out there? don't hear much about them here. I got a 88 liberator with twin 350's and alphas. I got the motors out for a freshining up over the winter :winker: .
Who's got a Four Winns Liberator ??
cartman
2,001 - 2,020 of 2,041 Posts
Joined
·
16 Posts
I have a 241 with a single 460 and im in need of a prop to help me get on plane easier. Im not to concerned about losing top end. Can anyone help?
Posted via Speedwake Mobile
have you dug thru this thread? seems to be the only place you can find info on the liberators. I'm just getting into restoring mine. twin 270's with omc drives outdrives are done interior cushions done, need some time to get the motors purring. to many projects. but glad to see this thread is still going
Joined
·
13 Posts
When my engine was stock, I ran a mercury mirage plus 19 pitch. Seemed to be the best performing prop for hole shot and top end. Put your trim tabs all the way down when taking off too.
Posted via Speedwake Mobile
Joined
·
2 Posts
Here's my 211 Liberator. Been in the family for 15 years. 350 with a new Sterndrive Engineering SE106 drive. LOVE this boat. Just had some paint work done from the rub rail up and from the tape stripe down, new interior, and had the transom redone.
Attachments
Joined
·
37 Posts
Thats got to be like getting rid of one of the kids when you see the Pride and Joy pull out of the yard!!!:laugh: Hate to see ya part way with your toy....
Yep...been wrenching and ordering parts all day here for the scarab. Thru bolted both swim platforms and made sure everything was sealed up hanging off the transom. Lot of work and upkeep, both worth it in the end.
Yep...been wrenching and ordering parts all day here for the scarab. Thru bolted both swim platforms and made sure everything was sealed up hanging off the transom. Lot of work and upkeep, both worth it in the end.
Joined
·
37 Posts
You might have to wind up doing like I did on my ski boat.....change the entire piece, just look for one that is close as you can get to what you have....there is always fleabay.
Joined
·
16 Posts
Well we just returned home from the jobbie nooner party on Lake St.Clair. What an awesome weekend!! And the 241 ran like a champ!
Joined
·
16 Posts
Posted via Speedwake Mobile
Looking to put thru hull exhaust on my 241. Anyone have any input on where to start?
Joined
·
8,839 Posts
Either at the exhaust risers or behind the transom...
Had to do it
Are you thinking the stock style? Out the sides and with the muffler/water boxes?
Otherwise if straight out the back like most rigs, I would just look for a set of tips with proper transom angles and 4" hose.
A 4" hole saw, some resin and sealer, hose clamps, and your in business
Good luck.
Had to do it
Are you thinking the stock style? Out the sides and with the muffler/water boxes?
Otherwise if straight out the back like most rigs, I would just look for a set of tips with proper transom angles and 4" hose.
A 4" hole saw, some resin and sealer, hose clamps, and your in business
Good luck.
Joined
·
37 Posts
If you can make a template about any fab shop can do some in stainless for you, the cost is not expensive as you may think.
Joined
·
8,839 Posts
Pretty common failure on the Libs.
A few people have remade their own or had them made like mentioned by Scarab One above there.
Some others I have seen replaced with a few different styles.
I was able to save mine years ago with a couple simple welds, but they weren't too bad.
If you do a little searching here and other boating forums, there has been quite a bit of discussion.
Good luck.
A few people have remade their own or had them made like mentioned by Scarab One above there.
Some others I have seen replaced with a few different styles.
I was able to save mine years ago with a couple simple welds, but they weren't too bad.
If you do a little searching here and other boating forums, there has been quite a bit of discussion.
Good luck.
2,001 - 2,020 of 2,041 Posts
-
?
-
?
-
?
-
?
-
?
-
?
-
?
-
?
-
?
-
?
-
?
-
?
-
?
-
?
-
?
-
?
-
?
-
?
-
?
-
?
